PORSCHE 944 TORQUE
Can't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
Stoptech front 14 inch 4 piston big brake kit Porsche 964 Carrera 91-94
Stoptech big brake kits give your vehicle that supercar look and feel, and exceed stock brake system performance in two areas. First, larger rotors increase heat capacity. A brake system?s biggest enemy is heat. A brake system with inadequate heat capacity will overheat leading to brake fade, increased stopping distances, and possible failure. Second, stiffer calipers and stainless steel lines reduce system compliance and increase initial bite and pedal feedback. The key is to increase heat capacity and reduce compliance without upsetting the stock front to rear brake torque ratio. If the brake upgrade you select adds too much front ...(choose a part on the right to read more)
General Fitment 911 1989-94
$3,126.60
Make a selection
M&m street-sport muffler system for 2009- 997.2 / 997.2s
Facts:
- + 15 crank hp & + 13 crank torque
- 2 ½” (63.5 mm) diameter tubing (reduces thermal stress)
- replaces OEM primary and secondary mufflers
- reuses OEM headers and 600 cell cats (no cel, retains OEM software)
- weighs 20.94 lbs. (9.5 kg)
- 33 lb. Weight savings over factory system
- t 316 stainless steel for improved durability over t 304
- uses the spring lock race system design to dampen vibration
- intoxicating growl at idle, partial throttle and wide open throttle
- no dme programming necessary
-reuses factory tips or any aftermarket tip designed to fit OEM exhaust (3.6 l models will require 3.8 l tips due to diameter diff...(choose a part on the right to read more)
General Fitment 911 2005-08
$2,660.90
Make a selection
Stoptech big brake kit rear drilled yellow caliper Porsche 997 GT3 rs 2007
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that op...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11 911 TURBO/GT2 2007-09
$3,126.60
Make a selection
Stoptech big brake kit front slotted black caliper Porsche 997 GT3 rs 2007
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that op...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$3,882.60
Make a selection
Stoptech big brake kit front slotted black caliper Porsche 997 turbo 2007
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that opt...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09
$3,882.60
Make a selection
Stoptech big brake kit front slotted black caliper Porsche 996 Carrera 4 2004
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that...(choose a part on the right to read more)
General Fitment 911 1998-05 911 2005-08
$3,126.60
Make a selection
Stoptech big brake kit front slotted red caliper Porsche 996 Carrera 4s 2004
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that ...(choose a part on the right to read more)
General Fitment 911 1998-05 911 2005-08
$3,126.60
Make a selection
Stoptech big brake kit rear slotted black caliper Porsche 996 GT2 2004
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that optima...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2001-05 911 GT3 2003-05
$3,126.60
Make a selection
The 996 turbo 68mm version is designed to function with the factory 68mm throttle body that was OEM on all 996 factory turbos. The 68mm plenum delivers similar power as the larger 74mm competition plenum.
Horsepower gains range from 30 to 35 above the stock power band, and initial boost response is vastly improved. The ipd plenum delivers more power and more torque giving the 996 turbo a stronger mid range and top end. The 68mm plenum version is perfect for the turbo customer looking to improve engine performance on both stock and moderately modified turbos developing under 700 horsepower. The ipd 996 turbo plenum will truly transform the already impressive turbo performance. The plenum should be the firs...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2001-05
$1,343.25
Make a selection
Sport driving demands the best products. That's why the sachs engineers have developed the sachs power clutch, a heavy duty clutch kit system with street manners and racetrack brawn. Features increased torque capacity designed for street use. Pressure plates are engineered with increased clamping force and the driving disc incorporate linings with increased coefficient of friction. Kit includes disc, pressure plate and throw out bearing.
Note: for vehicles with rubber center disc. Requires clutch release bearing guide tube (r95011681306) for installation.
View/Change Diagram
Ipd intake plenum non e-gas Porsche 996 3.4l 98-99
The ipd plenums are a unique design that dramatically increases horsepower and torque by optimizing air flow efficiency. Air flow is managed through a diversion splitter that maximizes air speed into the engine. The charged intake air maintains a higher velocity by replacing the factory plastic "t" intake with a stronger and more efficient cast aluminum "y" design. This unique "y" style plenum optimizes flow, improving acceleration and boost response. The new ipd replacement plenum eliminates the turbulent air flow by smoothly splitting and diverting the air flow and directing it towards the cylinders at a much higher air speed. This simple bolt-on ...(choose a part on the right to read more)
General Fitment 911 1998-05
$1,208.25
Make a selection
Ipd intake plenum Porsche 996 3.4l 99-01
The ipd plenums are a unique design that dramatically increases horsepower and torque by optimizing air flow efficiency. Air flow is managed through a diversion splitter that maximizes air speed into the engine. The charged intake air maintains a higher velocity by replacing the factory plastic "t" intake with a stronger and more efficient cast aluminum "y" design. This unique "y" style plenum optimizes flow, improving acceleration and boost response. The new ipd replacement plenum eliminates the turbulent air flow by smoothly splitting and diverting the air flow and directing it towards the cylinders at a much higher air speed. This simple bolt-on plenum upg...(choose a part on the right to read more)
General Fitment 911 1998-05
$1,208.25
Make a selection
All of the ipd "competition" plenums utilize the next largest size throttle body offered by Porsche. In this case, the competition Carrera upgrades the factory oe 74mm throttle body with Porsche's 82mm 997 GT3 throttle body. All of our competition plenums are designed to perform with cars equipped with high performance exhaust systems. The more extensive the exhaust system (headers, kats and mufflers) the better. Optimizing air intake and exhaust together creates a balanced performance package that allows the engine to inhale and exhale more air thus creating more power and torque.
Gains vary depending on pre-existing mods and quality of after-market exhaust installed. As we all "should" know, horsep...(choose a part on the right to read more)
General Fitment 911 1998-05
$1,208.25
Make a selection
Higher transmittable torque. Higher clamping load. Less abrasion. Direct replacement for the oe pressure plate. 240 mm. Max torque: 486 lb/ft (660 nm) weighs: 9.5 lbs. (4.3 kg) the reinforced sachs performance pressure plate (clutch cover) has fundamental advantages against an oe pressure plate, such as a higher transmittable torque and higher resistance against thrust. It also allows for faster and sportier gearshifts. That makes it extremely useful for street tuning, endurance races and hill climbing. The sachs performance clutches are assembled by hand. This guarantees the highest quality attributes in clamping load and release characteristics. Installation notes for those with single mass flywheel kits: whe...(choose a part on the right to read more)
View/Change Diagram
From $634.70
Make a selection
Stoptech big brake kit front slotted red caliper Porsche 997 GT2 2008
first, larger rotors increase heat capacity, allowing a driver to brake harder stop-after-stop with reduced chance of fade. Second, stiffer calipers and stainless steel lines reduce system compliance, providing consistent pedal feel .the key, however, is to increase heat capacity and reduce compliance without upsetting a vehicle's stock front-to-rear brake torque ratio. That is why stoptech developed the balanced brake upgrade design philosophy, which precisely apportions front and rear braking resources while factoring in vehicle weight transfer under braking.every stoptech balanced big brake kit is engineered to produce that optimal...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09 911 GT3 2007-11
$3,882.60
Make a selection
Speed technologies over the years have become the leader in providing the daily 700hp plus driven Porsche 996tt with the proper exhaust and accessories. With 20 years of experiences, the result is a line of superior performing exhausts for a variety of Porsche automobiles.
Speedtech has engineered to have a rich, deep tone in the lower rpms and a pronounced flat six note at higher rpms. With this new designed speedtech adds substantial horsepower and torque gains, along with improved throttle response are achieved with the free flowing, unrestrictive 70mm design. The 70mm tubing is utilized throughout, including the outlet pipes, which reduces back pressure and enables quick turbo response. The speedtech ...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2001-05
$3,233.25
Make a selection
Speed technologies over the years have become the leader in providing the daily 700hp plus driven Porsche 996tt with the proper exhaust and accessories. With 20 years of experiences, the result is a line of superior performing exhausts for a variety of Porsche automobiles.
Speedtechs new hi-flow headers constructed of t304 stainless steel enable additional flow capacity for modified cars. The hi-flow is a smooth merged collector and a perfect fit. Also they developed a unique, exotic sound that has to be heard to be appreciated. Along with incorporating their free flowing, straight through design, which increase torque and horsepower.
Specifications:
Stainless steel
General Fitment 911 TURBO/GT2 2001-05
$1,348.65
Make a selection
With the insane results of our aluminum y-pipe kit for the Porsche panamera turbo, we wanted to step up the luxury look of the engine bay with a full carbon fiber version. this carbon fiber y-pipe is a full replacement and includes everything you need to install in place of the original.
Looking at the stock y design in front of the throttle body, we new there was improvements to be made. This throttle body is the same size as the Cayenne tt throttle body we use on our 996tt and 997tt upgrade kits. The stock y-pipe is a 2 piece plastic y design that is smooth on the inside with a "deflector" internally to channel air. The bad part about the stock one is it goes from a 78mm id at the throttle body down to...(choose a part on the right to read more)
General Fitment PANAMERA 2010-14
$1,849.95
Make a selection
Speed technologies over the years have become the leader in providing the daily 700hp plus driven Porsche 996tt with the proper exhaust and accessories. With 20 years of experiences, the result is a line of superior performing exhausts for a variety of Porsche automobiles.
Speedtech has just released a their new sytem of exhaust design with x-cellerator cross-flow exhaust system. The cross flow designed to offer the discerning Porsche enthusiast the ultimate exhaust system with a number of performance and sound options in one complete package. The cross-flow designed by combining the exhaust pulses from both sides of the Porsche boxer motor with an "x" of "cross-flow" at the center of the muffler. Als...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2001-05
Speed technologies over the years have become the leader in providing the daily 700hp plus driven Porsche 996tt with the proper exhaust and accessories. With 20 years of experiences, the result is a line of superior performing exhausts for a variety of Porsche automobiles.
Speedtech has just released a their new sytem of exhaust design with x-cellerator cross-flow exhaust system. The cross flow designed to offer the discerning Porsche enthusiast the ultimate exhaust system with a number of performance and sound options in one complete package. The cross-flow designed by combining the exhaust pulses from both sides of the Porsche boxer motor with an "x" of "cross-flow" at the center of the muffler. Als...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09
$1,822.50
Make a selection
Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
Even though ...(choose a part on the right to read more)
$1,495.95
Make a selection
Agency power has developed and tested this exhaust system for the Porsche 987 Boxster and Cayman vehicles. The all t304 stainless steel exhaust features a mirror polished finished, thick flanges, OEM fit, and an incredible sound. The twin muffler exhaust system can be used with the OEM exhaust tip or our optional dual style chrome exhaust tip. The exhaust tip is easily fitted on to the OEM y-pipe and can be adjusted as needed. The exhaust is more free flowing with the reduction of the 2 additional catalytic converters.
The exhaust will then give you much better throttle response compared to the stock system. Producing an amazing sound which gives the Porsche a race tone, this exhaust is still comfortable for...(choose a part on the right to read more)
General Fitment BOXSTER 2005-08 CAYMAN 2006-08
$1,095.95
Make a selection
This new agency power y-pipe gets rid of 70% of the stock boost hose length and reduces the bend by about 45 degrees for a straight shot to the intercooler. For those customers wanting maximum efficiency, we supply a 3inch piece of aluminum and a coupler to be welded to aftermarket endtanks. With absolutely no changes to the cars configuration, the y-pipe added 21whp and 24ft/lbs of torque to your 911 turbo. This is quite an impressive bolt on gain that also added style and potential scalable performance to the car.
This part fits all 2001-2005 Porsche 996 turbo, x50, and GT2. Available in gloss black, mat black, silver, yellow, blue, gun metal, orange, red, and white; please indicate color choice when order...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2001-05
$1,249.95
Make a selection
Agency power has just given Porsche 996tt owners another way to get an easy 20 bolt-on horsepower with this new big mouth plenum and throttle body kit. agency power set out to engineer and design a plenum that was functional, did not require additional tuning, and simply. Made power! the plenum is 6061 aluminum that retains the same shape as the factory t pipe. the reason to keep a standard t shape is that the engine works off of pulses. just like how Porsche designed, agency power kept this design and simply improved the restriction, the throttle body. the factory throttle body inlet size is 76mm that then jumps up to a 78mm id plastic plenum.
Agency power has chosen to use a 78mm Cayenne turbo thro...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2001-05
All of the ipd "competition" plenums utilize the next largest size throttle body offered by Porsche. In this case, the competition Carrera upgrades the factory oe 74mm throttle body with Porsches 82mm 997 GT3 throttle body. All of our competition plenums are designed to perform with cars equipped with high performance exhaust systems. The more extensive the exhaust system (headers, kats and mufflers) the better. Optimizing air intake and exhaust together creates a balanced performance package that allows the engine to inhale and exhale more air thus creating more power and torque.
Gains vary depending on pre-existing mods and quality of after-market exhaust installed. As we all "should" know, horsepow...(choose a part on the right to read more)
General Fitment 911 2005-08
$1,208.25
Make a selection
© 2024 Automobile Atlanta Inc.
505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844
|